Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking updates from David Miller:
 "Highlights:

   1) Support SPI based w5100 devices, from Akinobu Mita.

   2) Partial Segmentation Offload, from Alexander Duyck.

   3) Add GMAC4 support to stmmac driver, from Alexandre TORGUE.

   4) Allow cls_flower stats offload, from Amir Vadai.

   5) Implement bpf blinding, from Daniel Borkmann.

   6) Optimize _ASYNC_ bit twiddling on sockets, unless the socket is
      actually using FASYNC these atomics are superfluous.  From Eric
      Dumazet.

   7) Run TCP more preemptibly, also from Eric Dumazet.

   8) Support LED blinking, EEPROM dumps, and rxvlan offloading in mlx5e
      driver, from Gal Pressman.

   9) Allow creating ppp devices via rtnetlink, from Guillaume Nault.

  10) Improve BPF usage documentation, from Jesper Dangaard Brouer.

  11) Support tunneling offloads in qed, from Manish Chopra.

  12) aRFS offloading in mlx5e, from Maor Gottlieb.

  13) Add RFS and RPS support to SCTP protocol, from Marcelo Ricardo
      Leitner.

  14) Add MSG_EOR support to TCP, this allows controlling packet
      coalescing on application record boundaries for more accurate
      socket timestamp sampling.  From Martin KaFai Lau.

  15) Fix alignment of 64-bit netlink attributes across the board, from
      Nicolas Dichtel.

  16) Per-vlan stats in bridging, from Nikolay Aleksandrov.

  17) Several conversions of drivers to ethtool ksettings, from Philippe
      Reynes.

  18) Checksum neutral ILA in ipv6, from Tom Herbert.

  19) Factorize all of the various marvell dsa drivers into one, from
      Vivien Didelot

  20) Add VF support to qed driver, from Yuval Mintz"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1649 commits)
  Revert "phy dp83867: Fix compilation with CONFIG_OF_MDIO=m"
  Revert "phy dp83867: Make rgmii parameters optional"
  r8169: default to 64-bit DMA on recent PCIe chips
  phy dp83867: Make rgmii parameters optional
  phy dp83867: Fix compilation with CONFIG_OF_MDIO=m
  bpf: arm64: remove callee-save registers use for tmp registers
  asix: Fix offset calculation in asix_rx_fixup() causing slow transmissions
  switchdev: pass pointer to fib_info instead of copy
  net_sched: close another race condition in tcf_mirred_release()
  tipc: fix nametable publication field in nl compat
  drivers: net: Don't print unpopulated net_device name
  qed: add support for dcbx.
  ravb: Add missing free_irq() calls to ravb_close()
  qed: Remove a stray tab
  net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettings
  net: ethernet: fec-mpc52xx: use phydev from struct net_device
  bpf, doc: fix typo on bpf_asm descriptions
  stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set
  net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettings
  net: ethernet: fs-enet: use phydev from struct net_device
  ...

1 files changed, 18 insertions, 2 deletions

diff --git a/Documentation/networking/dsa/dsa.txt b/Documentation/networking/dsa/dsa.txt
index 3b196c304b73..631b0f7ae16f 100644
--- a/Documentation/networking/dsa/dsa.txt
+++ b/Documentation/networking/dsa/dsa.txt
@@ -334,7 +334,7 @@ more specifically with its VLAN filtering portion when configuring VLANs on top
 of per-port slave network devices. Since DSA primarily deals with
 MDIO-connected switches, although not exclusively, SWITCHDEV's
 prepare/abort/commit phases are often simplified into a prepare phase which
-checks whether the operation is supporte by the DSA switch driver, and a commit
+checks whether the operation is supported by the DSA switch driver, and a commit
 phase which applies the changes.
 
 As of today, the only SWITCHDEV objects supported by DSA are the FDB and VLAN
@@ -533,7 +533,7 @@ Bridge layer
   out at the switch hardware for the switch to (re) learn MAC addresses behind
   this port.
 
-- port_stp_update: bridge layer function invoked when a given switch port STP
+- port_stp_state_set: bridge layer function invoked when a given switch port STP
   state is computed by the bridge layer and should be propagated to switch
   hardware to forward/block/learn traffic. The switch driver is responsible for
   computing a STP state change based on current and asked parameters and perform
@@ -542,6 +542,12 @@ Bridge layer
 Bridge VLAN filtering
 ---------------------
 
+- port_vlan_prepare: bridge layer function invoked when the bridge prepares the
+  configuration of a VLAN on the given port. If the operation is not supported
+  by the hardware, this function should return -EOPNOTSUPP to inform the bridge
+  code to fallback to a software implementation. No hardware setup must be done
+  in this function. See port_vlan_add for this and details.
+
 - port_vlan_add: bridge layer function invoked when a VLAN is configured
   (tagged or untagged) for the given switch port
 
@@ -552,6 +558,12 @@ Bridge VLAN filtering
   function that the driver has to call for each VLAN the given port is a member
   of. A switchdev object is used to carry the VID and bridge flags.
 
+- port_fdb_prepare: bridge layer function invoked when the bridge prepares the
+  installation of a Forwarding Database entry. If the operation is not
+  supported, this function should return -EOPNOTSUPP to inform the bridge code
+  to fallback to a software implementation. No hardware setup must be done in
+  this function. See port_fdb_add for this and details.
+
 - port_fdb_add: bridge layer function invoked when the bridge wants to install a
   Forwarding Database entry, the switch hardware should be programmed with the
   specified address in the specified VLAN Id in the forwarding database
@@ -565,6 +577,10 @@ of DSA, would be the its port-based VLAN, used by the associated bridge device.
   the specified MAC address from the specified VLAN ID if it was mapped into
   this port forwarding database
 
+- port_fdb_dump: bridge layer function invoked with a switchdev callback
+  function that the driver has to call for each MAC address known to be behind
+  the given port. A switchdev object is used to carry the VID and FDB info.
+
 TODO
 ====