diff options
Diffstat (limited to 'Documentation/devicetree/bindings/media/samsung-s5c73m3.txt')
-rw-r--r-- | Documentation/devicetree/bindings/media/samsung-s5c73m3.txt | 97 |
1 files changed, 0 insertions, 97 deletions
diff --git a/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt deleted file mode 100644 index f0ea9adad442..000000000000 --- a/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt +++ /dev/null @@ -1,97 +0,0 @@ -Samsung S5C73M3 8Mp camera ISP ------------------------------- - -The S5C73M3 camera ISP supports MIPI CSI-2 and parallel (ITU-R BT.656) video -data busses. The I2C bus is the main control bus and additionally the SPI bus -is used, mostly for transferring the firmware to and from the device. Two -slave device nodes corresponding to these control bus interfaces are required -and should be placed under respective bus controller nodes. - -I2C slave device node ---------------------- - -Required properties: - -- compatible : "samsung,s5c73m3"; -- reg : I2C slave address of the sensor; -- vdd-int-supply : digital power supply (1.2V); -- vdda-supply : analog power supply (1.2V); -- vdd-reg-supply : regulator input power supply (2.8V); -- vddio-host-supply : host I/O power supply (1.8V to 2.8V); -- vddio-cis-supply : CIS I/O power supply (1.2V to 1.8V); -- vdd-af-supply : lens power supply (2.8V); -- xshutdown-gpios : specifier of GPIO connected to the XSHUTDOWN pin; -- standby-gpios : specifier of GPIO connected to the STANDBY pin; -- clocks : should contain list of phandle and clock specifier pairs - according to common clock bindings for the clocks described - in the clock-names property; -- clock-names : should contain "cis_extclk" entry for the CIS_EXTCLK clock; - -Optional properties: - -- clock-frequency : the frequency at which the "cis_extclk" clock should be - configured to operate, in Hz; if this property is not - specified default 24 MHz value will be used. - -The common video interfaces bindings (see video-interfaces.txt) should be used -to specify link from the S5C73M3 to an external image data receiver. The S5C73M3 -device node should contain one 'port' child node with an 'endpoint' subnode for -this purpose. The data link from a raw image sensor to the S5C73M3 can be -similarly specified, but it is optional since the S5C73M3 ISP and a raw image -sensor are usually inseparable and form a hybrid module. - -Following properties are valid for the endpoint node(s): - -endpoint subnode ----------------- - -- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in - video-interfaces.txt. This sensor doesn't support data lane remapping - and physical lane indexes in subsequent elements of the array should - be only consecutive ascending values. - -SPI device node ---------------- - -Required properties: - -- compatible : "samsung,s5c73m3"; - -For more details see description of the SPI busses bindings -(../spi/spi-bus.txt) and bindings of a specific bus controller. - -Example: - -i2c@138a000000 { - ... - s5c73m3@3c { - compatible = "samsung,s5c73m3"; - reg = <0x3c>; - vdd-int-supply = <&buck9_reg>; - vdda-supply = <&ldo17_reg>; - vdd-reg-supply = <&cam_io_reg>; - vddio-host-supply = <&ldo18_reg>; - vddio-cis-supply = <&ldo9_reg>; - vdd-af-supply = <&cam_af_reg>; - clock-frequency = <24000000>; - clocks = <&clk 0>; - clock-names = "cis_extclk"; - xshutdown-gpios = <&gpf1 3 1>; - standby-gpios = <&gpm0 1 1>; - port { - s5c73m3_ep: endpoint { - remote-endpoint = <&csis0_ep>; - data-lanes = <1 2 3 4>; - }; - }; - }; -}; - -spi@1392000 { - ... - s5c73m3_spi: s5c73m3@0 { - compatible = "samsung,s5c73m3"; - reg = <0>; - ... - }; -}; |