diff options
Diffstat (limited to 'drivers/net/phy/qt2025.rs')
| -rw-r--r-- | drivers/net/phy/qt2025.rs | 103 |
1 files changed, 103 insertions, 0 deletions
diff --git a/drivers/net/phy/qt2025.rs b/drivers/net/phy/qt2025.rs new file mode 100644 index 000000000000..28d8981f410b --- /dev/null +++ b/drivers/net/phy/qt2025.rs @@ -0,0 +1,103 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (C) Tehuti Networks Ltd. +// Copyright (C) 2024 FUJITA Tomonori <fujita.tomonori@gmail.com> + +//! Applied Micro Circuits Corporation QT2025 PHY driver +//! +//! This driver is based on the vendor driver `QT2025_phy.c`. This source +//! and firmware can be downloaded on the EN-9320SFP+ support site. +//! +//! The QT2025 PHY integrates an Intel 8051 micro-controller. + +use kernel::c_str; +use kernel::error::code; +use kernel::firmware::Firmware; +use kernel::net::phy::{ + self, + reg::{Mmd, C45}, + DeviceId, Driver, +}; +use kernel::prelude::*; +use kernel::sizes::{SZ_16K, SZ_8K}; + +kernel::module_phy_driver! { + drivers: [PhyQT2025], + device_table: [ + DeviceId::new_with_driver::<PhyQT2025>(), + ], + name: "qt2025_phy", + author: "FUJITA Tomonori <fujita.tomonori@gmail.com>", + description: "AMCC QT2025 PHY driver", + license: "GPL", + firmware: ["qt2025-2.0.3.3.fw"], +} + +struct PhyQT2025; + +#[vtable] +impl Driver for PhyQT2025 { + const NAME: &'static CStr = c_str!("QT2025 10Gpbs SFP+"); + const PHY_DEVICE_ID: phy::DeviceId = phy::DeviceId::new_with_exact_mask(0x0043a400); + + fn probe(dev: &mut phy::Device) -> Result<()> { + // Check the hardware revision code. + // Only 0x3b works with this driver and firmware. + let hw_rev = dev.read(C45::new(Mmd::PMAPMD, 0xd001))?; + if (hw_rev >> 8) != 0xb3 { + return Err(code::ENODEV); + } + + // `MICRO_RESETN`: hold the micro-controller in reset while configuring. + dev.write(C45::new(Mmd::PMAPMD, 0xc300), 0x0000)?; + // `SREFCLK_FREQ`: configure clock frequency of the micro-controller. + dev.write(C45::new(Mmd::PMAPMD, 0xc302), 0x0004)?; + // Non loopback mode. + dev.write(C45::new(Mmd::PMAPMD, 0xc319), 0x0038)?; + // `CUS_LAN_WAN_CONFIG`: select between LAN and WAN (WIS) mode. + dev.write(C45::new(Mmd::PMAPMD, 0xc31a), 0x0098)?; + // The following writes use standardized registers (3.38 through + // 3.41 5/10/25GBASE-R PCS test pattern seed B) for something else. + // We don't know what. + dev.write(C45::new(Mmd::PCS, 0x0026), 0x0e00)?; + dev.write(C45::new(Mmd::PCS, 0x0027), 0x0893)?; + dev.write(C45::new(Mmd::PCS, 0x0028), 0xa528)?; + dev.write(C45::new(Mmd::PCS, 0x0029), 0x0003)?; + // Configure transmit and recovered clock. + dev.write(C45::new(Mmd::PMAPMD, 0xa30a), 0x06e1)?; + // `MICRO_RESETN`: release the micro-controller from the reset state. + dev.write(C45::new(Mmd::PMAPMD, 0xc300), 0x0002)?; + // The micro-controller will start running from the boot ROM. + dev.write(C45::new(Mmd::PCS, 0xe854), 0x00c0)?; + + let fw = Firmware::request(c_str!("qt2025-2.0.3.3.fw"), dev.as_ref())?; + if fw.data().len() > SZ_16K + SZ_8K { + return Err(code::EFBIG); + } + + // The 24kB of program memory space is accessible by MDIO. + // The first 16kB of memory is located in the address range 3.8000h - 3.BFFFh. + // The next 8kB of memory is located at 4.8000h - 4.9FFFh. + let mut dst_offset = 0; + let mut dst_mmd = Mmd::PCS; + for (src_idx, val) in fw.data().iter().enumerate() { + if src_idx == SZ_16K { + // Start writing to the next register with no offset + dst_offset = 0; + dst_mmd = Mmd::PHYXS; + } + + dev.write(C45::new(dst_mmd, 0x8000 + dst_offset), (*val).into())?; + + dst_offset += 1; + } + // The micro-controller will start running from SRAM. + dev.write(C45::new(Mmd::PCS, 0xe854), 0x0040)?; + + // TODO: sleep here until the hw becomes ready. + Ok(()) + } + + fn read_status(dev: &mut phy::Device) -> Result<u16> { + dev.genphy_read_status::<C45>() + } +} |