summaryrefslogtreecommitdiff
path: root/include
diff options
context:
space:
mode:
Diffstat (limited to 'include')
-rw-r--r--include/linux/i2c/adp8860.h154
-rw-r--r--include/linux/lcd.h23
-rw-r--r--include/linux/mfd/pcf50633/backlight.h51
-rw-r--r--include/linux/mfd/pcf50633/core.h4
4 files changed, 232 insertions, 0 deletions
diff --git a/include/linux/i2c/adp8860.h b/include/linux/i2c/adp8860.h
new file mode 100644
index 000000000000..0b4d39855c91
--- /dev/null
+++ b/include/linux/i2c/adp8860.h
@@ -0,0 +1,154 @@
+/*
+ * Definitions and platform data for Analog Devices
+ * Backlight drivers ADP8860
+ *
+ * Copyright 2009-2010 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __LINUX_I2C_ADP8860_H
+#define __LINUX_I2C_ADP8860_H
+
+#include <linux/leds.h>
+#include <linux/types.h>
+
+#define ID_ADP8860 8860
+
+#define ADP8860_MAX_BRIGHTNESS 0x7F
+#define FLAG_OFFT_SHIFT 8
+
+/*
+ * LEDs subdevice platform data
+ */
+
+#define ADP8860_LED_DIS_BLINK (0 << FLAG_OFFT_SHIFT)
+#define ADP8860_LED_OFFT_600ms (1 << FLAG_OFFT_SHIFT)
+#define ADP8860_LED_OFFT_1200ms (2 << FLAG_OFFT_SHIFT)
+#define ADP8860_LED_OFFT_1800ms (3 << FLAG_OFFT_SHIFT)
+
+#define ADP8860_LED_ONT_200ms 0
+#define ADP8860_LED_ONT_600ms 1
+#define ADP8860_LED_ONT_800ms 2
+#define ADP8860_LED_ONT_1200ms 3
+
+#define ADP8860_LED_D7 (7)
+#define ADP8860_LED_D6 (6)
+#define ADP8860_LED_D5 (5)
+#define ADP8860_LED_D4 (4)
+#define ADP8860_LED_D3 (3)
+#define ADP8860_LED_D2 (2)
+#define ADP8860_LED_D1 (1)
+
+/*
+ * Backlight subdevice platform data
+ */
+
+#define ADP8860_BL_D7 (1 << 6)
+#define ADP8860_BL_D6 (1 << 5)
+#define ADP8860_BL_D5 (1 << 4)
+#define ADP8860_BL_D4 (1 << 3)
+#define ADP8860_BL_D3 (1 << 2)
+#define ADP8860_BL_D2 (1 << 1)
+#define ADP8860_BL_D1 (1 << 0)
+
+#define ADP8860_FADE_T_DIS 0 /* Fade Timer Disabled */
+#define ADP8860_FADE_T_300ms 1 /* 0.3 Sec */
+#define ADP8860_FADE_T_600ms 2
+#define ADP8860_FADE_T_900ms 3
+#define ADP8860_FADE_T_1200ms 4
+#define ADP8860_FADE_T_1500ms 5
+#define ADP8860_FADE_T_1800ms 6
+#define ADP8860_FADE_T_2100ms 7
+#define ADP8860_FADE_T_2400ms 8
+#define ADP8860_FADE_T_2700ms 9
+#define ADP8860_FADE_T_3000ms 10
+#define ADP8860_FADE_T_3500ms 11
+#define ADP8860_FADE_T_4000ms 12
+#define ADP8860_FADE_T_4500ms 13
+#define ADP8860_FADE_T_5000ms 14
+#define ADP8860_FADE_T_5500ms 15 /* 5.5 Sec */
+
+#define ADP8860_FADE_LAW_LINEAR 0
+#define ADP8860_FADE_LAW_SQUARE 1
+#define ADP8860_FADE_LAW_CUBIC1 2
+#define ADP8860_FADE_LAW_CUBIC2 3
+
+#define ADP8860_BL_AMBL_FILT_80ms 0 /* Light sensor filter time */
+#define ADP8860_BL_AMBL_FILT_160ms 1
+#define ADP8860_BL_AMBL_FILT_320ms 2
+#define ADP8860_BL_AMBL_FILT_640ms 3
+#define ADP8860_BL_AMBL_FILT_1280ms 4
+#define ADP8860_BL_AMBL_FILT_2560ms 5
+#define ADP8860_BL_AMBL_FILT_5120ms 6
+#define ADP8860_BL_AMBL_FILT_10240ms 7 /* 10.24 sec */
+
+/*
+ * Blacklight current 0..30mA
+ */
+#define ADP8860_BL_CUR_mA(I) ((I * 127) / 30)
+
+/*
+ * L2 comparator current 0..1106uA
+ */
+#define ADP8860_L2_COMP_CURR_uA(I) ((I * 255) / 1106)
+
+/*
+ * L3 comparator current 0..138uA
+ */
+#define ADP8860_L3_COMP_CURR_uA(I) ((I * 255) / 138)
+
+struct adp8860_backlight_platform_data {
+ u8 bl_led_assign; /* 1 = Backlight 0 = Individual LED */
+
+ u8 bl_fade_in; /* Backlight Fade-In Timer */
+ u8 bl_fade_out; /* Backlight Fade-Out Timer */
+ u8 bl_fade_law; /* fade-on/fade-off transfer characteristic */
+
+ u8 en_ambl_sens; /* 1 = enable ambient light sensor */
+ u8 abml_filt; /* Light sensor filter time */
+
+ u8 l1_daylight_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l1_daylight_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l2_office_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l2_office_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l3_dark_max; /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
+ u8 l3_dark_dim; /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
+
+ u8 l2_trip; /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
+ u8 l2_hyst; /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
+ u8 l3_trip; /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
+ u8 l3_hyst; /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
+
+ /**
+ * Independent Current Sinks / LEDS
+ * Sinks not assigned to the Backlight can be exposed to
+ * user space using the LEDS CLASS interface
+ */
+
+ int num_leds;
+ struct led_info *leds;
+ u8 led_fade_in; /* LED Fade-In Timer */
+ u8 led_fade_out; /* LED Fade-Out Timer */
+ u8 led_fade_law; /* fade-on/fade-off transfer characteristic */
+ u8 led_on_time;
+
+ /**
+ * Gain down disable. Setting this option does not allow the
+ * charge pump to switch to lower gains. NOT AVAILABLE on ADP8860
+ * 1 = the charge pump doesn't switch down in gain until all LEDs are 0.
+ * The charge pump switches up in gain as needed. This feature is
+ * useful if the ADP8863 charge pump is used to drive an external load.
+ * This feature must be used when utilizing small fly capacitors
+ * (0402 or smaller).
+ * 0 = the charge pump automatically switches up and down in gain.
+ * This provides optimal efficiency, but is not suitable for driving
+ * loads that are not connected through the ADP8863 diode drivers.
+ * Additionally, the charge pump fly capacitors should be low ESR
+ * and sized 0603 or greater.
+ */
+
+ u8 gdwn_dis;
+};
+
+#endif /* __LINUX_I2C_ADP8860_H */
diff --git a/include/linux/lcd.h b/include/linux/lcd.h
index c67fecafff90..8877123f2d6e 100644
--- a/include/linux/lcd.h
+++ b/include/linux/lcd.h
@@ -69,6 +69,29 @@ struct lcd_device {
struct device dev;
};
+struct lcd_platform_data {
+ /* reset lcd panel device. */
+ int (*reset)(struct lcd_device *ld);
+ /* on or off to lcd panel. if 'enable' is 0 then
+ lcd power off and 1, lcd power on. */
+ int (*power_on)(struct lcd_device *ld, int enable);
+
+ /* it indicates whether lcd panel was enabled
+ from bootloader or not. */
+ int lcd_enabled;
+ /* it means delay for stable time when it becomes low to high
+ or high to low that is dependent on whether reset gpio is
+ low active or high active. */
+ unsigned int reset_delay;
+ /* stable time needing to become lcd power on. */
+ unsigned int power_on_delay;
+ /* stable time needing to become lcd power off. */
+ unsigned int power_off_delay;
+
+ /* it could be used for any purpose. */
+ void *pdata;
+};
+
static inline void lcd_set_power(struct lcd_device *ld, int power)
{
mutex_lock(&ld->update_lock);
diff --git a/include/linux/mfd/pcf50633/backlight.h b/include/linux/mfd/pcf50633/backlight.h
new file mode 100644
index 000000000000..83747e217b27
--- /dev/null
+++ b/include/linux/mfd/pcf50633/backlight.h
@@ -0,0 +1,51 @@
+/*
+ * Copyright (C) 2009-2010, Lars-Peter Clausen <lars@metafoo.de>
+ * PCF50633 backlight device driver
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ */
+
+#ifndef __LINUX_MFD_PCF50633_BACKLIGHT
+#define __LINUX_MFD_PCF50633_BACKLIGHT
+
+/*
+* @default_brightness: Backlight brightness is initialized to this value
+*
+* Brightness to be used after the driver has been probed.
+* Valid range 0-63.
+*
+* @default_brightness_limit: The actual brightness is limited by this value
+*
+* Brightness limit to be used after the driver has been probed. This is useful
+* when it is not known how much power is available for the backlight during
+* probe.
+* Valid range 0-63. Can be changed later with pcf50633_bl_set_brightness_limit.
+*
+* @ramp_time: Display ramp time when changing brightness
+*
+* When changing the backlights brightness the change is not instant, instead
+* it fades smooth from one state to another. This value specifies how long
+* the fade should take. The lower the value the higher the fade time.
+* Valid range 0-255
+*/
+struct pcf50633_bl_platform_data {
+ unsigned int default_brightness;
+ unsigned int default_brightness_limit;
+ uint8_t ramp_time;
+};
+
+
+struct pcf50633;
+
+int pcf50633_bl_set_brightness_limit(struct pcf50633 *pcf, unsigned int limit);
+
+#endif
+
diff --git a/include/linux/mfd/pcf50633/core.h b/include/linux/mfd/pcf50633/core.h
index 3398bd9aab11..ad411a78870c 100644
--- a/include/linux/mfd/pcf50633/core.h
+++ b/include/linux/mfd/pcf50633/core.h
@@ -18,6 +18,7 @@
#include <linux/regulator/driver.h>
#include <linux/regulator/machine.h>
#include <linux/power_supply.h>
+#include <linux/mfd/pcf50633/backlight.h>
struct pcf50633;
@@ -43,6 +44,8 @@ struct pcf50633_platform_data {
void (*force_shutdown)(struct pcf50633 *);
u8 resumers[5];
+
+ struct pcf50633_bl_platform_data *backlight_data;
};
struct pcf50633_irq {
@@ -152,6 +155,7 @@ struct pcf50633 {
struct platform_device *mbc_pdev;
struct platform_device *adc_pdev;
struct platform_device *input_pdev;
+ struct platform_device *bl_pdev;
struct platform_device *regulator_pdev[PCF50633_NUM_REGULATORS];
};